Fabricant | Modèle | Produit | Caractéristiques | Ajouter à la sélection |
---|---|---|---|---|
AILTECH | 7615 | Noise Source | 0.01-1.5 GHz 15.5 dB ENR, N(m), 28 VDC |
+ |
AILTECH | 7616 | Noise Source | 1-12.4 GHz 15.5 dB ENR, N(m), 28 VDC |
+ |
AILTECH | 7617 | Noise Source | 12.4-18 GHz 15.5 dB ENR, SMA(f), 28 VDC |
+ |
AILTECH | 7650-114 | Noise Generator | 379-441 MHz 37.0 dB ENR, N(m), 28 VDC |
+ |
AILTECH | 7650-115 | Noise Generator | 28-32 MHz 37.0 dB ENR, N(m), 28 VDC |
+ |
AILTECH | 7650-79 | Noise Source | 50-90 MHz 15.5 dB ENR, N(m), 28 VDC |
+ |
ANRITSU | 2000-768 | DIN-7/16 female Short-Open-Load Calibration Tee | DC-4 GHz DC-12.4 GHz, 2 Watts, SMA(m/f) |
+ |
EATON/AILTECH | 7660-147 | Noise Source | 230-270 MHz 35.5 dB ENR, SMA(f), 28VDC |
+ |
EATON/AILTECH | 7650-055 | Noise Source | 2.55-2.85 GHz 15.5 dB ENR, N(m), 28VDC |
+ |
FXR/MICROLAB | HM-10N | Signal Sampler | DC-5 GHz 10 dB coupling, 2.5 dB ins.loss,Nm/f/f |
+ |
GENERAL RADIO | 1442-F | 5 Ohm Resistance Standard | DC-100 MHz usable to 100 MHz, two GR900 ports |
+ |
HP/KEYSIGHT | 08566-60003 | Mixer Bias Protection Network | DC-6 GHz BNC(f/f) |
+ |
HP/KEYSIGHT | 11665B | Modulator | 0.15-18 GHz N(m/f), for use with HP 8755/6/7 |
+ |
HP/KEYSIGHT | 11853A | Accessory Kit | DC-18 GHz 50 Ohm type n (one each 11511A/11512A N female/male short; two each N female/female and N male/male adapters) |
+ |
HP/KEYSIGHT | 11866A | Short/ Open/ Load Kit | DC-2 GHz APC7 ; load is 909C, 1.005 VSWR |
+ |
HP/KEYSIGHT | 35678A | Type N Cal | DC-18 GHz Kit, c/o 1 each 909C-012,200, 909C-013,200, male&female shorts, N(m/m) & N(f/f) adapters |
+ |
HP/KEYSIGHT | 5356D | Harmonic Mixer Driver | 36-110 GHz adapts 5345A/5355A to 11970 series harmonic mixers |
+ |
HP/KEYSIGHT | 83572A-001,006 | RF Sweeper Plug-in | 26.5-40 GHz +3 dBm, pulse/square wave and external levelling, for HP 8350B |
+ |
HP/KEYSIGHT | 85025C | Detector Adapter | DC-18 GHz for HP 8757 sderies scalar network analyzers |
+ |
HP/KEYSIGHT | 85032E | Calibration Kit | DC-18 GHz Type N Economy |
+ |
HP/KEYSIGHT | 85036B | Calibration Kit | DC-18 GHz 75 Ohm type N |
+ |
HP/KEYSIGHT | 85050B | 7mm Calibration Kit | DC-18 GHz for HP 8510/ 8720 |
+ |
HP/KEYSIGHT | 85051A | 7mm Verification Kit | DC-18 GHz for HP 8510 |
+ |
HP/KEYSIGHT | 8710-1766 | APC7 Torque Wrench | 6.5-15 GHz 12 lb.-in. |
+ |
HP/KEYSIGHT | U8487A | Thermocouple Power Sensor | 10 MHz-50 GHz -35/+20 dBm range, built-in DC block, 2.4mm male input |
+ |
MAURY MICROWAVE | 8650P | TNC Short-Open-Load Calibration Kit | DC-18 GHz includes (1 each male & female) termination, open, short, male-male, female-female; (2 each) APC7 adapters to male & female - no VNA disks included |
+ |
MAURY MICROWAVE | 8780M | OSP male Short/ Open/ Load Calibration Kit | DC-18 GHz RF/LO=1-2800 MHz, LO=+26 dBm, IF=1-2000 MHz, SMA(f/f/f) |
+ |
MAURY MICROWAVE | 8780N-opt.01 | OSP (male) Short/ Open/ Load Calibration Kit | DC-6 GHz RF/LO=4-8 GHz, LO=+7 dBm, IF=DC-3 GHz, SMA(f/f/f) |
+ |
MAURY MICROWAVE | A007A | Gage Kit | DC-18 GHz N (male & female) |
+ |
MAURY MICROWAVE | A020A | Gage Kit | DC-18 GHz Type N connector (male & female) |
+ |
MAURY MICROWAVE | A027 | Boxed set of two hand held gages measure SMA male and female center contacts | DC-34 GHz RF/LO=5-18 GHz, LO=+7 dBm, IF=DC-6 GHz, SMA(f/f/f) |
+ |
MAURY MICROWAVE | A028D2 | 7mm Master Gage | DC-18 GHz for 7mm VNA calibration kit |
+ |
MAURY MICROWAVE | MT-7118A | Cryogenic Termination | DC-18 GHz APC7 |
+ |
MICRONETICS | NOD-5107 | Noise Generator | 100 Hz-100 MHz -70 dBm per Hz, or +10 dBm max., 0-10 dB step attenuator, SMA(f) output, 120VAC power |
+ |
MICRONETICS | NOD-5108 (sma) | Noise Generator | 100 Hz-100 MHz 0-10 dB step attenuator, -75 dBm/Hz, or +10 dBm maximum, SMA(f) output, 120VAC power |
+ |
MICRONETICS | NOD-5108 (n) | Noise Generator | 100 Hz-100 MHz 0-10 dB step attenuator, -75 dBm/Hz, or +10 dBm maximum, N(f) output, 120VAC power |
+ |
NARDA | 466B | Thermocouple Power Monitor Sensor | 10 MHz-12.4 GHz 1-100mW, Nm |
+ |
NARDA | 466B | Power Monitor | 0.01-12.4 GHz 1-100 mW, for Narda meter |
+ |
OMNI-SPECTRA | 2598-5238-54 | Set of two OSP gages: male pin & female pin | 20 dB, 4-8 GHz, SMA(f/f) | + |
OMNI-SPECTRA | 2598-5239-54 | Set of two OSP gages: male pin & female pin | 16 dB, 8-18 GHz, SMA(f/f) | + |
OMNI-SPECTRA | 4098-5029-54 | SMA male Pin & Dielectric Gage Kit | DC-18 GHz in case with depth standard |
+ |
PASTERNACK | PE-9504 | 2.4mm male to N male Adapter | DC-18 GHz 40 dB, 800-950 MHz, SMA(f/f) |
+ |
PICOSECOND PULSE LABS | 5070A | 70 nS Delay Line | DC-18 GHz SMA(f/f) |
+ |
TEKTRONIX | 015-0385-00 | External Mixer Diplexer | DC-18 GHz for Tektronix 490/2750 series spec.an. |
+ |
TEKTRONIX | CT-2 / P6041 | Current Transformer | 1 millvolt per milliamp, into 50 Ohms | + |
WILTRON | 3666 | Verification Kit | DC-26.5 GHz 3.5mm : 360 disk; 19S50-7 3.5mm airline; 19S50-7B 3.5mm BEATTY AIRLINE; 42S-20 & 42S-50 20 dB & 50 dB attenuators |
+ |
WILTRON | 6400-6N75 | SWR Autotester | 1-1000 MHz 75 Ohm N, 40 dB dir.,for 6400 series |
+ |
WILTRON | 6400-6N75-1 | SWR Autotester | 1-2000 MHz 5 Ohm N, 38 dB dir.,for 6400 series |
+ |